Graco Marine Sanitation System 224434 User Manual

INSTRUCTIONS-PARTS LIST  
307013  
Rev. V  
This manual contains important  
warnings and information.  
READ AND KEEP FOR REFERENCE.  
First choice when  
quality counts.t  
INSTRUCTIONS  
45:1 Ratio Kingr Pump  
4050 psi (28 MPa, 279 bar) Maximum Working Pressure  
90 psi (0.6 MPa, 6.2 bar) Maximum Air Input Pressure  
Model 224434, Series A  
Stubby Size, with Standard Air Motor and  
Severe-Duty Displacement Pump*, with leather packings  
*Severe-Duty Displacement Pumps have an abrasion  
and corrosion-resistant displacement rod and sleeve.  
Refer to the Technical Data in the separate displace-  
ment pump manual 307728 for Wetted Parts informa-  
tion.  
03290  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441  
ECOPYRIGHT 1997, GRACO INC.  
Graco Inc. is registered to I.S. EN ISO 9001  
 
WARNING  
FIRE AND EXPLOSION HAZARD  
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and  
result in fire or explosion and serious injury.  
D Ground the equipment and the object being sprayed/dispensed. See Grounding on page 4.  
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being  
sprayed.  
D Extinguish all the open flames or pilot lights in the spray/dispensing area.  
D Electrically disconnect all the equipment in the spray/dispensing area.  
D Keep the spray/dispensing area free of debris, including solvent, rags, and gasoline.  
D Do not turn on or off any light switch in the spray/dispensing area while operating or if fumes are  
present.  
D Do not smoke in the spray/dispensing area.  
D Do not operate a gasoline engine in the spray/dispensing area.  
D If there is any static sparking while using the equipment, stop spraying/dispensing immediately.  
Identify and correct the problem.  
EQUIPMENT MISUSE HAZARD  
Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result  
in a serious injury.  
INSTRUCTIONS  
D This equipment is for professional use only.  
D Read all the instruction manuals, tags, and labels before operating the equipment.  
D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco  
distributor.  
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.  
D Check the equipment daily. Repair or replace worn or damaged parts immediately.  
D Do not exceed the maximum working pressure of the lowest rated system component. This equip-  
ment has a 4050 psi (28.3 MPa, 283 bar) maximum working pressure.  
D Use fluids that are compatible with the equipment wetted parts. See the Technical Data section of  
all the equipment manuals. Read the fluid manufacturers warnings.  
D Route the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not  
expose Graco hoses to temperatures above 180_F (82_C) or below 40_F (40_C).  
D Do not use the hoses to pull equipment.  
D Wear hearing protection when operating this equipment.  
D Comply with all applicable local, state, and national fire, electrical, and other safety regulations.  
MOVING PARTS HAZARD  
Moving parts, such as the air motor piston, can pinch or amputate fingers.  
D Do not operate the equipment with the air motor plates removed.  
D Keep clear of any moving parts when starting or operating the equipment.  
307013  
3
 
Installation  
D All solvent pails used when flushing, according to  
Grounding  
local code. Use only metal pails, which are conduc-  
tive. Do not place the pail on a non-conductive  
surface, such as paper or cardboard, which inter-  
rupts grounding continuity.  
WARNING  
FIRE AND EXPLOSION HAZARD  
Before operating, ground the system as  
explained below. Also read the section  
FIRE AND EXPLOSION HAZARD on  
page 3.  
D To maintain grounding continuity when flushing or  
relieving pressure, always hold a metal part of the  
gun firmly to the side of a grounded metal pail, then  
trigger the gun.  
W
To reduce the risk of static sparking, ground the pump  
and all other components used or located in the spray/  
dispensing area. Check your local electrical code for  
detailed instructions for your area and type of equip-  
ment and be sure to ground all of these components.  
X
Y
Z
D Pump: loosen the grounding lug locknut (W) and  
2
washer (X). Insert one end of a 12 ga (1.5 mm )  
minimum ground wire (Y) into the slot in lug (Z) and  
tighten the locknut securely. See Fig. 1. Connect  
the other end of the wire to a true earth ground.  
Order Part No. 237569 Ground Wire and Clamp.  
0864  
Fig. 1  
Flushing Safety  
D Air and Fluid Hoses: Use only electrically conduc-  
tive hoses with a maximum of 500 feet (150 m)  
combined hose length to ensure grounding continu-  
ity.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 7.  
D Air Compressor: follow the air compressor  
manufacturers recommendations  
Before flushing, be sure the entire system and flushing  
pails are properly grounded. Refer to Grounding at  
left. Follow the Pressure Relief Procedure on page  
7, and remove the spray tip/nozzle from the gun/dis-  
pensing valve. Always use the lowest possible fluid  
pressure, and maintain firm metal-to-metal contact  
between the gun/dispensing valve and the pail during  
flushing to reduce the risk of fluid injection injury, static  
sparking, and splashing.  
D Spray gun/dispensing valve: obtain grounding  
through connection to a properly grounded fluid  
hose and pump.  
D Fluid supply container: according to local code.  
D Object being sprayed: according to local code.  
4
307013  
 
Installation  
Typical Installation  
Y
C
H
A
D
L
E
B
N
P
(PLUG WHEN EXHAUSTING  
THROUGH MUFFLER)  
R
F
G
S
J
K
Key  
A
B
C
D
E
F
G
H
J
Pump  
Pump Runaway Valve  
Air Line Lubricator  
Bleed-Type Master Air Valve (required, for pump)  
Pump Air Regulator  
Air Line Filter  
Bleed-Type Master Air Valve (for accessories)  
Air Supply Hose  
Fluid Drain Valve (required)  
Fluid Supply Hose  
M
K
L
Spray Gun  
M
N
P
R
S
Y
Fluid Suction Hose  
Exhaust Port for Muffler (11/4npt)  
16 Exhaust Holes  
Wall Bracket  
Packing Nut/Wet-Cup  
Ground Wire (required)  
03291  
307013  
5
 
Installation  
NOTE: Reference numbers and letters in parentheses  
Use an electrically conductive 3/4 in. ID (minimum) air  
in the text refer to the callouts in the figures and the  
parts drawing.  
hose (H) to supply air to the pump.  
Air Line Accessories  
NOTE: Accessories are available from your Graco  
distributor. If you supply your own accessories, be sure  
the are adequately sized and pressure-rated to meet  
the systems requirements.  
Install the following accessories in the order shown in  
the Typical Installation, using adapters as necessary:  
D An air line lubricator (C) provides automatic air  
The Typical Installation shown on page 5 is only a  
guide for selecting and installing system components  
and accessories. Contact your Graco distributor for  
assistance in designing a system to suit your particular  
needs.  
motor lubrication.  
D A bleed-type master air valve (D) is required in  
your system to relieve air trapped between it and  
the motor when the valve is closed (see the WARN-  
ING at left). Be sure the bleed valve is easily ac-  
cessible from the pump, and is located downstream  
from the air regulator.  
System Accessories  
Refer to the Typical Installation on page 5.  
D A pump runaway valve (B) senses when the  
pump is running too fast and automatically shuts off  
the air to the motor. A pump which runs too fast can  
be seriously damaged. Install closest to the pump  
air inlet.  
WARNING  
Two accessories are required in your system: a  
bleed-type master air valve (D) and a fluid drain  
valve (J). These accessories help reduce the risk  
of serious injury including splashing in the eyes or  
on the skin, and injury from moving parts if you are  
adjusting or repairing the pump.  
D An air regulator (E) controls pump speed and  
outlet pressure by adjusting the air pressure to the  
pump. Locate the regulator close to the pump, but  
upstream from the bleed-type master air valve.  
The bleed-type master air valve relieves air trapped  
between this valve and the pump after the air is  
shut off. Trapped air can cause the pump to cycle  
unexpectedly. Locate the valve close to the pump.  
D An air line filter (F) removes harmful dirt and  
moisture from the compressed air supply.  
The fluid drain valve assists in relieving fluid pres-  
sure in the displacement pump, hose, and gun.  
Triggering the gun to relieve pressure may not be  
sufficient.  
D A second bleed-type air valve (G) isolates the air  
line accessories for servicing. Locate upstream  
from all other air line accessories.  
Fluid Line Accessories  
Mounting Accessories  
Install the following accessories in the order shown in  
the Typical Installation, using adapters as necessary:  
Mount the pump (A) to suit the type of installation  
planned. The pump dimensions and mounting hole  
layout are shown on page 14. Use 3/8 in. bolts, lock-  
washers, and nuts to attach the pump firmly to the  
mounting.  
D A fluid drain valve (J) is required in your system  
to relieve fluid pressure in the hose and gun (see  
the WARNING at left).  
Air and Fluid Hoses  
D A spray gun (L) dispenses the fluid. The gun  
shown in the Typical Installation is an airless spray  
gun.  
Be sure all air and fluid hoses are properly sized and  
pressure-rated for your system. Use only electrically  
conductive air and fluid hoses. Fluid hoses must have  
spring guards on both ends.  
Air Motor Exhaust  
Connect a electrically conductive fluid hose (H) to the  
pumps 1npt(f) fluid outlet, using a suitable adapter.  
To route the air motor exhaust outside, remove the  
exhaust port plug and connect the hose to the 11/4  
npt(f) exhaust port (N). Plug the 16 exhaust holes in  
the base of the motor with 1/4 in. size x 1/2 in. long  
self-tapping screws.  
Connect a fluid suction hose and tube (M) to the  
pumps 11/2npt(f) fluid intake.  
6
307013  
 
Operation  
Pressure Relief Procedure  
1. Lock the spray gun/dispensing valve trigger safety.  
WARNING  
INJECTION HAZARD  
2. Shut off the air to the pump.  
3. Close the bleed-type master air valve (required in  
your system).  
Fluid under high pressure can be in-  
jected through the skin and cause  
serious injury. To reduce the risk of an  
injury from injection, splashing fluid, or moving  
parts, follow the Pressure Relief Procedure  
whenever you:  
4. Unlock the trigger safety.  
5. Hold a metal part of the gun/valve firmly to the side  
of a grounded metal pail, and trigger the gun/valve  
to relieve pressure.  
6. Lock the trigger safety.  
D are instructed to relieve the pressure,  
D stop spraying,  
7. Open the drain valve (required in your system),  
having a container ready to catch the drainage.  
D check or service any of the system equipment,  
D or install or clean any part of the system.  
8. Leave the drain valve open until you are ready to  
spray again.  
If you suspect that the spray tip/nozzle is completely  
clogged, or that pressure has not been fully relieved  
after following the steps above, very slowly loosen the  
retaining nut or hose end coupling and relieve pressure  
gradually, then loosen completely. Now clear the  
tip/nozzle or hose.  
307013  
7
 
Operation  
In a direct supply system, with the pump and lines  
WARNING  
primed and with adequate air pressure and volume  
supplied, the pump will start and stop as the spray gun  
is opened and closed. In a circulating system, the  
pump will run continuously and will speed up or slow  
down as supply demands until the air supply is shut  
off.  
Moving parts can pinch or amputate your fingers or  
other body parts. When air is supplied to the motor,  
the air motor piston (located behind the air motor  
shield) moves. Therefore, never operate the pump  
with the ar motor shield removed.  
Use an adequately sized air regulator (E) to control the  
pump speed and the fluid pressure. Always use the  
lowest air pressure necessary to get the desired  
results. Higher pressures waste fluid and cause pre-  
mature wear of the pump packings and spray tip.  
Flush the Pump Before Using  
The pump is tested with lightweight motor oil, which is  
left in to protect the pump parts. If the fluid you are  
pumping may be contaminated by the oil, flush out the  
oil with a compatible solvent before using the pump. If  
the pump is being used to supply a circulating system,  
allow the solvent to circulate until the pump is thor-  
oughly flushed.  
Keep the packing nut/wet-cup (S) half filled with Graco  
Throat Seal Liquid (TSL) or compatible solvent, to help  
prolong the packing life. Adjust the packing nut weekly  
with the wrench (supplied) so it is just tight enough to  
prevent leakage; do not overtighten. Always relieve  
the pressure before adjusting the packing nut.  
WARNING  
For your safety, read the warning section, FIRE  
AND EXPLOSION HAZARD on page 3 before  
flushing, and follow all instructions given there.  
Never allow the pump to run dry of the fluid being  
pumped. A dry pump will quickly accelerate to a high  
speed, possibly damaging itself. A pump runaway  
valve (B), which shuts off the air supply to the pump if  
the pump accelerates beyond the pre-set speed, is  
available. See the Typical Installation on page 5. If  
your pump accelerates quickly, or is running too fast,  
stop it immediately and check the fluid supply. If the  
supply container is empty and air has been pumped  
into the lines, refill the container and prime the pump  
and the lines with fluid, or flush and leave it filled with a  
compatible solvent. Be sure to eliminate all air from the  
fluid system.  
Starting and Adjusting the Pump  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 7.  
See the Typical Installation on page 5. Be sure the air  
regulator (E) and bleed-type master air valve (D) are  
closed. Do not install the spray tip yet.  
Shutdown and Care of the Pump  
For overnight shutdown, relieve the pressure. Always  
stop the pump at the bottom of the stroke to prevent  
the fluid from drying on the exposed displacement rod  
and damaging the throat packings.  
Connect a suction hose (M) to the pumps fluid inlet.  
Hold a metal part of the spray gun (L) firmly to the side  
of a grounded metal pail and hold the trigger open.  
Then open the pumps bleed-type master air valve (D).  
Now slowly open the air regulator until the pump starts,  
about 20 psi (140 kPa, 1.4 bar).  
Always flush the pump before the fluid dries on the  
displacement rod. Never leave water or water-based  
fluid in the pump overnight. First, flush with water or a  
compatible solvent, then with mineral spirits. Relieve  
the pressure, but leave the mineral spirits in the pump  
to protect the parts from corrosion.  
Cycle the pump slowly until all the air is pushed out,  
and fluid is flowing from the gun in a steady stream.  
Release the spray gun trigger and lock the trigger  
safety. The pump should stall against pressure when  
the trigger is released.  
Check Valve Adjustment  
Relieve the pressure, then install the spray tip in the  
gun.  
Refer to the separate displacement pump manual  
307728 for check valve adjustment information.  
8
307013  
 
Troubleshooting  
Before servicing this equipment always make sure to  
WARNING  
Relieve the Pressure.  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 7.  
Note: Check all possible causes and solutions before  
disassembling the pump.  
Problem  
Cause  
Solution  
Restricted line or inadequate air supply  
Clear; increase air supply.  
Pump fails to operate  
Obstructed fluid hose, gun, or dispensing Open, clear.*  
valve  
Exhausted fluid supply  
Refill; Purge all air from pump and fluid  
lines.  
Fluid dried on displacement rod  
Clean; always stop pump at bottom of  
stroke; keep wet-cup 1/2 filled with com-  
patible solvent.  
Damaged air motor  
Service air motor (see manual 306968).  
Clear; increase air supply.  
Restricted line or inadequate air supply  
Pump operates but output low on both  
strokes  
Obstructed fluid hose, gun, or dispensing Open, clear.*  
valve  
Exhausted fluid supply  
Refill; purge all air from pump and fluid  
lines.  
Air in displacement pump and hose  
Check valves need adjustment  
Packing nut too tight or too loose  
Worn throat packings  
Reprime.  
Adjust (see manual 307728).  
Adjust (see manual 307728).  
Replace (see manual 307728).  
Clear; service (see manual 307728).  
Pump operates but output low on  
down stroke  
Held open or worn intake valve  
Pump operates but output low on up  
stroke  
Held open or worn fluid piston valve or  
packings  
Clear, service (see manual 307728).  
Exhausted fluid supply  
Refill; purge all air from pump and fluid  
lines.  
Erratic or accelerated operation  
Packing nut too tight  
Adjust (see manual 307728).  
Check valves need adjustment  
Held open or worn intake valve  
Adjust (see manual 307728).  
Clear; service (see manual 307728).  
Clear; service (see manual 307728).  
Held open or worn fluid piston valve or  
packings  
* To determine if the fluid hose or gun/valve is obstructed, relieve the pressure. Disconnect the fluid hose and place a container  
at the pump fluid outlet to catch any fluid. Turn on the air just enough to start the pump (about 20–40 psi [140–280 kPa, 1.4–2.8  
bar]). If the pump starts when the air is turned on, the obstruction is in the fluid hose gun/valve.  
307013  
9
 
Service  
Reconnecting the Displacement Pump  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 7.  
1. Orient the pumps fluid outlet (A) to the air motors  
air inlet (B) as was noted in step 2 under Discon-  
necting the Displacement Pump. Position the  
displacement pump (2) on the tie rods (31).  
Disconnecting the Displacement Pump  
2. Place the coupling nut (32) on the connecting rod  
(T). Insert the couplers (33) into the coupling nut  
from the top. Screw the coupling nut (32) onto the  
air motor piston rod. Screw the locknuts (26) onto  
the tie rods (31) loosely.  
1. Flush the pump, if possible. Stop the pump at the  
bottom of its stroke. Relieve the pressure.  
2. Disconnect the air and fluid hoses. Remove the  
pump from its mounting. Note the relative position  
of the pumps fluid outlet (A) to the air motors air  
inlet (B). See Fig. 2.  
3. Mount the pump and reconnect all hoses. Recon-  
nect the ground wire if it was disconnected during  
repair.  
3. Screw the coupling nut (32) off of the air motor  
piston rod. Be careful not to lose the two couplers  
(33) as you lower the nut. Unscrew the tie rod  
locknuts (26) from the tie rods (31). Carefully pull  
the displacement pump (2) away from the air  
motor (1).  
4. Tighten the tie rod locknuts (109) evenly, and  
torque to 4050 ft-lb (5468 NSm).  
5. Tighten the packing nut/wet-cup (S) with the  
wrench (28) supplied, so it is just snug - no tighter.  
Fill the wet-cup 1/2 full with Graco Throat Seal  
Liquid (TSL) or compatible solvent. Start the pump  
and run it slowly at about 20 psi (140 kPa, 1.4 bar)  
air pressure, to check that it is operating properly.  
4. Refer to the instruction manual 307728 (supplied)  
for displacement pump service instructions.  
5. Refer to instruction manual 306968 (supplied) for  
air motor service instructions.  
10  
307013  
 
Service  
1
2
Torque to 4050 ft-lb  
(5468 NSm)  
Torque to 145155 ft-lb  
(195210 NSm)  
1
B
33  
32  
31  
1
2
T
S
26  
1
28  
A
2
Model 224434 shown  
03293  
Fig. 2  
307013  
11  
 
Parts  
Model 224434, Series A  
Stubby Size, with Standard Air Motor and  
Severe-Duty Displacement Pump with leather  
packings  
Includes items 133  
1
Ref.  
No.  
Part No. Description  
Qty.  
1
207647  
224435  
AIR MOTOR  
See Manual 306968 for parts  
DISPLACEMENT PUMP ASSY  
See Manual 307728 for parts  
NUT, lock; 5/811  
1
2
1
3
1
26  
28  
31  
101712  
102176  
167911  
WRENCH  
ROD. tie; 7(178 mm),  
shoulder-to-shoulder  
NUT, coupling  
3
1
1
32  
33  
186925  
184129  
COUPLING  
33  
32  
31  
26  
28  
2
03293  
12  
307013  
 
 
Notes  
307013  
13  
 
Dimensions  
Mounting Hole  
Layout  
See 306968 for  
Air Motor Dimensional Drawing.  
3.712”  
(94 mm)  
3.464”  
(88 mm)  
4.0”  
(102 mm)  
4.0”  
(102 mm)  
3/4 npt(f)  
AIR INLET  
2.0”  
(51 mm)  
A
3.712”  
(94 mm)  
1.875(48 mm)  
FOR OUTLET  
RISER TUBE  
0.44”  
(11.1 mm)  
DIA. (4)  
5/811 UNC (3)  
FOR PUMP  
ATTACHMENT  
B
1npt(f)  
FLUID OUTLET  
11/2npt(f)  
FLUID INTAKE  
WEIGHT: 110 lb (50 kg)  
03290  
Pump  
Model  
A
B
224434,  
42.5 in.  
(1079.5 mm)  
21 in.  
(533.4 mm)  
01838  
14  
307013  
 
Technical Data  
Category  
Data  
Maximum fluid working pressure  
Maximum air pressure (see cover)  
4050 psi (28 MPa, 279 bar)  
90 psi (0.6 MPa, 6.2 bar)  
Pump cycles per 1 gallon (3.8 liters) 16  
Fluid flow at 50 cpm  
Wetted parts  
3.3 gpm (12 liter/min)  
See displacement pump manual 307728  
Sound Pressure Levels (dBa)  
(measured at 1 meter from unit)  
Input Air Pressures at 15 cycles per minute  
0.28 MPa, 2.8 bar  
(40 psi)  
0.48 MPa, 4.8 bar  
(70 psi)  
0.6 MPa, 6.2 bar  
(90 psi)  
Air Motor  
King  
78.8  
82.7  
90.5  
Sound Power Levels (dBa)  
(tested in accordance with ISO 96142)  
Input Air Pressures at 15 cycles per minute  
0.28 MPa, 2.8 bar  
(40 psi)  
0.48 MPa, 4.8 bar  
(70 psi)  
0.6 MPa, 6.2 bar  
(90 psi)  
Air Motor  
King  
86.5  
88.8  
97.7  
Performance Chart  
To find Fluid Outlet Pressure (psi/MPa/bar) at a specific fluid flow  
(lpm/gpm) and operating air pressure (psi/MPa/bar):  
To find Pump Air Consumption (m#/min or scfm) at a specific fluid  
flow (lpm/gpm) and air pressure (psi/MPa/bar):  
1. Locate desired flow along bottom of chart.  
1. Locate desired flow along bottom of chart.  
2. Follow vertical line up to intersection with selected fluid outlet  
pressure curve (black). Follow left to scale to read fluid outlet  
pressure.  
2. Read vertical line up to intersection with selected air consumption  
curve (dashes). Follow left to scale to read air consumption.  
A
B
C
0.6 MPa, 6.2 bar (90 psi) air pressure  
0.5 MPa, 4.9 bar (70 psi) air pressure  
0.3 MPa, 2.8 bar (40 psi) air pressure  
Test Fluid: No. 10 Weight Oil  
Fluid Outlet Pressure  
Air Consumption  
psi  
MPa, bar  
4500  
scfm  
cycles per minute  
cycles per minute  
m#/min  
16  
32  
48  
64  
16  
32  
48  
64  
200  
5.60  
31.5, 315  
A
B
150  
A
3000  
4.20  
21, 210  
B
C
100  
2.80  
C
1500  
50  
10.5, 105  
1.40  
0
0
0
1
2
3
4
0
1
2
3
4
gpm  
gpm  
liters/minute  
liters/minute  
3.8  
7.6  
11.4  
15.2  
3.8  
7.6  
11.4  
15.2  
307013  
15  
 
The Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited  
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment  
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accor-  
dance with Gracos written recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-  
stitution of nonGraco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of  
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Gracos sole obligation and buyers sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-  
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires  
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
Graco Phone Number  
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:  
18003674023 Toll Free.  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Sales Offices: Minneapolis, Detroit  
Foreign Offices: Belgium, Korea, Hong Kong, Japan  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 554401441  
PRINTED IN U.S.A. 307013 August 1969, Revised May 2000  
16  
307013  
 

Grizzly Automobile Parts h6236 User Manual
HANNspree Flat Panel Television LT13 23H1 User Manual
Hasbro Games Evac Fighter Vehicle User Manual
Honeywell Network Cables 1061 User Manual
HP Hewlett Packard Car Video System f1903 User Manual
HP Hewlett Packard Computer Accessories 16501A LOGIC User Manual
HP Hewlett Packard Server BL860c User Manual
HP Hewlett Packard TV Converter Box 70900A User Manual
ICTC Holdings Corporation Paint Sprayer HRO ST3131 User Manual
IKEA Dishwasher IUD4000R User Manual